Checkline TI-25DL-MMX User Manual download pdf (Page 4)

– 4 –

3.2 Contents Of Kit

The TI-25M-MMX is supplied as a complete kit with the following:

a. Gauge

b. Two (2) AA batteries

(installed in gauge)

c. Probe/cable assembly

d. 4 oz. Bottle of coupling fluid

e. NIST-traceable calibration

certificate

f. Operating instruction manual

g. Foam-filled carrying case

3.3 Probe

The probe transmits and receives the ultrasonic sound waves which the

TI-25DL-MMX uses to calculate the thickness of the material being

measured. The probe must be used correctly in order for the

TI-25DL-MMX to produce accurate and reliable results.

A small amount of “coupling” fluid, commonly called “couplant” is used

to insure that there are no air gaps between the probe and the material

surface. Grasp the probe by the molded rubber grip and place it on top

of the material surface. Apply moderate pressure to the top surface of

the probe with your index finger (A) or thumb (B) to stabilize the probe

and to keep the wearface seated flat against the measurement surface.

Probe

Wearface

– 29 –

17.0 MATERIAL SAFETY DATA SHEET (MSDA)

Section 1— Product Identification

Product Name: TI-25M Generic Name: Ultrasonic Couplant

Manufacturer: Electromatic Equipt. Co. NFPA Hazardous Materials Identification System (est)

Health 0 Flammability 0 Reactivity 0

Section 2— Hazardous Ingredients

This material does not contain any ingredients having known health hazards in concentrations greater

than 1%. This material does not contain any known or suspected carcinogens.

Section 3 — Physical Data (nominal)

Boiling Point: >220°F Freezing Point: <20°F

Vapor Pressure: N/A Evaporation Rate: N/A

Specific Gravity: >1.0Z Solubility in Water: complete

pH: 7.35 – 7.9 Acoustic Imp.: 1.726x10

Vapor Density: N/A Appearance and Odor: water white, opaque gel; bland odor

Section 4 — Fire and Explosive Hazard Data

Flash Point: none Upper Exposure Limit: none Lower Exposure Limit: none

Special Fire Fighting Procedures: N/A Extinguishing media: N/A

Unusual Fire and Explosion Hazards: none

Section 5 — Reactive Data

Stability: Stable Conditions to Avoid: none

Incompatibility (Materials to Avoid): none known

Hazardous Polymerization: will not occur

Hazardous Decomposition or Byproducts: none known

Section 6 —- Health Hazard and First Aid Data

Routes of Entry

Skin: not likely Ingestion: not normally Eyes: not normally Inhalation: no

Effects of Overexposure:

Acute: May cause temporary eye irritation Chronic: none expected

First Aid Procedures:

Skin: Remove with water if desired. Eyes: Flush with water for 15 minutes.

Ingestion: For large quantities, induce vomiting and call a physician Inhalation: N/A

Section 7 - Storage and Handling Information

Precautions to be taken in handling and storage: Store between 20 °F and 120 °F. Spills are

slippery and should be cleaned up immediately. Steps to be taken in case material is released or spilled:

Pick up excess for disposal. Clean with water. Waste disposal method: Dispose of in accordance with

federal, state, and local regulations.

Section 8 — Control Measures

Respiratory Protection: not required Ventilation: not required

Protective Gloves: on individuals demonstrating sensitivity to TI-25M

Eye Protection: as required by working conditions Other Protective Equipment: not required

1. TI-25M-MMX contains only food grade and cosmetic grade ingredients.

1 2 3 4 5 6 7 8 9 ... 16 17

Comments to this Manuals

No comments

Checkline TI-25DL-MMX User Manual Page 4

Comments to this Manuals

Related products and manuals for Sensors Checkline TI-25DL-MMX